DIY Dodge Repairs and Maintenance

When does the Dodge Caliber Check Engine Light come on? (2023)

papanbiswasbd

The Dodge Caliber Check Engine Light is a warning indicator that the car’s engine has reached a threshold of damage.

When this light is on, it means that one or more of your vehicle’s systems are not working properly and require service.

When you turn on your engine, the Dodge Caliber Check Engine Light should come on immediately and remain on for about 20 seconds before shutting off automatically.

If it does not come on then check to make sure that there are no obstructions in front of it such as dirt or snow, or that there is not any oil or other substance blocking its opening. If none of these issues seem to be causing the problem, then it could be something else like a blown fuse or loose wire.

If you notice that the Dodge Caliber Check Engine Light turns off but then comes back on shortly after turning off again, this may mean that there is an issue with your vehicle’s emissions system and needs to be addressed by a professional mechanic as soon as possible before further damage occurs to other components within your vehicle’s engine compartment.

Dodge Caliber Check Engine Light Reset

Why Does the Dodge Caliber Check Engine Light Reset?

The Dodge Caliber Check Engine Light resets automatically when you start up the vehicle. If this light is on and you have not had any issues with your vehicle, it’s safe to say that there are no problems with your engine. However, if the light flashes or stays on after driving for some time, this could mean that there is an issue with your car.

Dodge Caliber Check Engine Light Reset

Should the Dodge Caliber Check Engine Light be reset by Service?

The Dodge Caliber Check Engine Light can be reset by service. This will tell you if there is an issue with your vehicle. If the light stays on or flashes after you have driven for some time, it’s best to bring your car into a professional mechanic as soon as possible before further damage occurs to other components within your vehicle’s engine compartment.

3 12

How to reset the Dodge Caliber Check Engine Light step by step?

If you are wondering how to perform the Dodge Caliber Check Engine light reset, follow the steps we have indicated.

1. Turn the ignition key to the “on” position and wait for the light to go off.

2. Open your car hood and look at the engine compartment.

3. Find where your battery is located on your Dodge Caliber (this should be near a terminal).

4. Using a wrench, remove one of the bolts that hold down your battery.

5. With the wrench still in hand, remove the other bolt that holds down your battery.

6. Lift out your battery and set it aside so you can get to work on resetting the check engine light.

7. Locate the positive (red) and negative (black) cables that are attached to your battery terminals and detach them from each other by hand .

8. Set your wrench on a clean area of your engine compartment and turn it counterclockwise until the nut holding down your battery is removed.

9. Remove the battery from its place, set it aside, and then put all of the items back in their original places so you don’t confuse yourself later on.

10. Clean off any dirt or debris from where your old battery was mounted (this will prevent any corrosion from building up).

1 13

11. Use a screwdriver to remove the negative battery cable from the post on your vehicle’s frame, and then use pliers to remove the positive cable.

12. Install your new battery by wrapping your positive cable around one post and then attaching it to the other. Then attach the negative wire in the same manner.

13. Put the battery back in its place, making sure that it is secure and that the cables are not pinched or touching anything else.

14. Check all terminals with a voltage meter to make sure that they are properly connected and have power flowing through them.

15. Start your car and let it run for a few minutes to charge the battery.

16. Reattach the battery cables to their respective posts.

17. Test your battery again by removing one terminal and then touching the other to it with a wire or small piece of metal. If you get spark, then your battery is good and recharged.

18. If the car still won’t start, then you will need to take it to a mechanic.

Rate this post

papanbiswasbd

DodgeAutoInsightHub

Hey there, fellow auto enthusiasts! We're the team behind DodgeAutoInsightHub, your go-to source for all things cars. As true car aficionados ourselves, we're thrilled to welcome you to our automotive community, where we eat, breathe, and dream cars, especially the iconic Dodges. Here, we're not just about machines; we're about the stories they tell, the adventures they take us on, and the endless possibilities they offer. From the latest Dodge innovations to tried-and-true car care tips, we're here to share the insights that fuel our passion. We're not just a team; we're a family of gearheads, tinkerers, and car geeks who are here to learn and grow together. So buckle up and join us on this exciting ride as we dive into the world of Dodge and beyond. Whether you're a seasoned auto pro or just starting your journey, there's a place for you here. Feel free to explore our content, ask questions, and share your own automotive experiences. Let's rev up the engines and embark on this road trip together – the DodgeAutoInsightHub way. Welcome aboard!

Leave a Reply

Your email address will not be published. Required fields are marked *

Back to top button